3.0
LAND DEVELOPMENT EQUIPMENT
3.1 |
|
3.2 |
|
3.3 |
|
||
Features: The
leveler consists of frame, 3-point linkage, cutting or scraping blade, and
thick curved sheet closed from sides to form a bucket. The scraping blade is
made from medium carbon steel or low alloy steel, hardened and tempered to
about 42 HRC. The blade is joined to the curved sheet with fasteners and can
be replaced after being worn out or becoming dull. The working depth of the
implement is controlled by hydraulic system of the tractor. |
||
Specifications: |
|
|
Length(
mm) |
:
1840 |
|
Width
(mm) |
:
700 |
|
Height
(mm) |
:
700 |
|
Size
of Blade (mm) -Length -Width
-Thickness |
:
1830 :
75 ;
8 |
|
Weight
(kg) |
:
90 |
|
Power
requirement (hp/kW) : 35/26.25 Uses:
Leveling
of fields and pulling or pushing loosened soil from one place to other. |
||
Approx
Cost: Rs. 20,000 |
||
3.2 LASER GUIDED LAND LEVELLER |
||
|
||
Features: The
laser land leveler consists of a laser transmitter, a laser receiver, an
electrical control panel, a twin solenoid hydraulic control valve, two wheels
and a leveling bucket. The laser transmitter transmits a laser beam, which is
intercepted by the laser receiver mounted on the leveling bucket. The control
panel mounted on the tractor interprets the signal from the receiver and
opens or closes the hydraulic control valve, which raises or lowers the
bucket. Some laser transmitters have the ability to operate over graded
slopes ranging from 0.01% to 15% and apply dual controlled slope in the
field. The leveling bucket can be either 3-point linkage mounted or pulled by
the tractor’s drawbar. Bucket dimensions, number of wheels and capacity will
vary according to the available power source and field conditions. |
||
Specifications: |
|
|
|
|
|
Laser
Source |
: < 5mw 635nm |
|
Operating
diameter( m) |
: (Above) 800 |
|
Grade
range (%) |
: –10 to +15 Dual
Axes |
|
Grade
accuracy (%) |
: 0.015, 3 mm@30 m |
|
Remote control type |
: Full 2-way
communication |
|
Power requirement (
hp/KW) : 60/45 Uses:
It is used for precision leveling of land in one
or both the directions. Approx
Cost: Rs. 3,50,000 |
||
|
||
3.3 SUB-SOILER
|
|
|
|
Features: It consists of beam made of
high carbon steel, beam supports which are flanged at upper and lower edges
for rigidity, hollow steel adaptor welded to the bottom end of the beam to
accommodates share base having square section, share plate made from high
carbon steel and shank drilled and counter bored for set board which secures
the base in the adaptor. Share plate is made from high carbon steel, hardened
and tempered to suitable hardness. Two symmetrically located bolt holes allow
reversibility of share. The working depth of the sub-soiler
is controlled by hydraulic system and linkage of tractor. Specifications: Length (mm)
: 600 Width (mm)
: 490 |
|
Height
(mm) |
: 1325 |
Maximum
working depth (mm) |
: 535 |
Weight
(kg) |
: 62 |
Power
requirement(hp/kW) |
: 55/41.25 |
Uses: It is used to break hardpan of
the soil, loosening of the soil and helps the water to seep into the soil for
improving drainage. A mole ball can be attached to create a small tunnel in
the soil, which serves as drainage channel for water. Cost of Machine : Rs.20,000/- |
|
|